|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Drip Irrigation
Supply Line Connectors
Please Note: Drip irrigation systems have the potential to leak and are designed primarily for greenhouse and outdoor applications. Do not attempt to use drip irrigation components in living areas where leaking water could cause damage unless proper catchment is provided.
|
|
|
|
|
|
|
|
Poly Tube Connector
1/2 Inch ID (.62in OD)
Connects 2 pieces of 1/2 inch poly tube to each other. This size is for use with 1/2 inch vinyl black tubing with an outside diameter of .62 inches. |
|
|
|
|
|
Used for continuing lengths of drip hose or to repair a damaged area. No glue or tools are required.
Recommended operating pressure 10 to 30 PSI with a maximum operating pressure of 60 PSI. Made of high impact UV resistant plastic. |
|
|
|
|
|
Order #0011995
Poly Tube Connector
1/2 (.62) Inch
.99 |
|
|
|
|
|
|
|
|
|
Poly Tube Elbow
1/2 Inch ID (.62in OD)
Connects 2 pieces of 1/2 inch poly tube to each other at a 90 degree angle. This size is for use with 1/2 inch vinyl black tubing with an outside diameter of .62 inches. |
 |
|
|
|
|
These elbows will help you make sharper turns than the poly tubing can normally take without kinking the supply tubing and cutting off the water flow. If you want the supply tubing to follow a fence line or a garden border, these are always handy to have.
Recommended operating pressure 10 to 30 PSI with a maximum operating pressure of 60 PSI. Made of high impact UV resistant plastic. |
|
|
|
|
|
Order #0011994
Poly Tube Elbow
1/2 (.62) Inch
1.49 |
|
|
|
|
|
|
|
|
|
Poly Tube Tee
1/2 Inch ID (.62in OD)
Connects 3 pieces of 1/2 inch poly tube. This size is for use with 1/2 inch vinyl black tubing with an outside diameter of .62 inches. These tees will help you tap into a main supply line of 1/2 inch poly tubing. When running a new line, occassionally you will have one smaller |
 |
|
|
|
|
area you couldn't quite cover. Placing a tee in the line will allow you to reach sections such as these. Always a smart idea to keep a few extra for when you plant new areas. If you have the extra pressure capacity and an existing supply line close, just tap into the supply line with one of these tees without having to create a whole new irrigation zone.
Recommended operating pressure 10 to 30 PSI with a maximum operating pressure of 60 PSI. Made of high impact UV resistant plastic. |
|
|
|
|
|
Order #0012001
Poly Tube Tee
1/2 (.62) Inch
1.49 |
|
|
|
|
|
|
|
|
|
Poly Tube
Flushable End Cap
1/2 Inch ID (.62in OD)
Terminates end of 1/2 inch poly tube run. Screw off cap allows for thorough flushing of drip lines. Standard 3/4in FHT garden hose thread. This size is for use with 1/2 inch vinyl black tubing with an outside diameter of .62 inches. |
 |
|
|
|
|
|
|
|
Order #DS-COMTHREND62G
Poly Tube
Flushable End Cap
1/2 (.62) Inch
1.59 |
|
|
|
|
|
|
|
|
|
|
|
|
|
Poly Tube
3/4 Inch Female Hose Thread
(FHT)
Adaptor
1/2 Inch ID (.62in OD)
3/4 inch Female Hose Thread Adaptor connects to 1/2 inch poly tubing. Use this on any standard 3/4 inch hose thread fitting to convert to .620 poly line. |
 |
|
|
|
|
|
|
Compression fitting ensures water tight connection. Includes screened washer in swivel. This size is for use with 1/2 inch vinyl black tubing with an outside diameter of .62 inches. Not for use with most hard vinyl black tubing.
Recommended operating pressure 10 to 30 PSI with a maximum operating pressure of 60 PSI. Made of high impact UV resistant plastic. |
|
|
|
|
|
|
|
Order #0015912
Poly Tube
3/4in FHT Adaptor
1/2 (.62) Inch
1.79 |
|
|
|
|
|
|
|
|
|
|
|
|
|
Poly Tube
3/4 Inch Female Hose Thread
(FHT) Tee Adaptor
1/2 Inch ID (.62in OD)
3/4 inch Female Hose Thread Adaptor connects to 1/2 inch poly tubing. Use this on any standard 3/4 inch hose thread fitting to convert to a tee fitting for .620 OD poly line. |
 |
|
|
|
|
|
|
Compression fitting ensures water tight connection. Includes screened washer in swivel. This size is for use with 1/2 inch vinyl black tubing with an outside diameter of .62 inches.
Recommended operating pressure 10 to 30 PSI with a maximum operating pressure of 60 PSI. Made of high impact UV resistant plastic. |
|
|
|
|
|
|
|
Order #DS-SWITEE62
Poly Tube
3/4in FHT Tee Adaptor
1/2 (.62) Inch
2.95 |
|
|
|
|
|
|
|
|
|
|
|
|
|
Pressure Regulators
Backflow Preventer
|
|
|
|
|
|
|
Inline Backflow Preventer
3/4 Inch
Female Hose Thread (FHT) to
3/4 Inch
Male Hose Thread (MHT)
Plastic inline backflow preventer has 3/4 inch Female Hose Thread on the inlet side, and 3/4 inch Male Hose Thread on the outlet side. Comes with rubber washer. Use this with the pressure regulators below. |
 |
|
|
|
|
|
|
Backflow preventers are used in most connection assemblies and you should always use one if you will be fertilizing through your drip system. This will always be the first component attached to your faucet.
Maximum operating inlet pressure is 100 PSI. Made of high impact UV resistant plastic. |
|
|
|
|
|
|
|
Order #0018001
Inline Backflow Preventer
3/4in FHT to 3/4in MHT
5.95 |
|
|
|
|
|
|
|
|
|
|
|
|
|
Standard Preset
Pressure Regulator 25PSI
3/4 Inch
Female Hose Thread (FHT) to
3/4 Inch
Male Hose Thread (MHT)
Preset pressure regulators are used to regulate the pressure in a drip line. |
 |
|
|
|
|
|
|
It is important that drip systems use a lower pressure than normal household water pressure (usually in the 60 PSI range) so that the drippers and/or sprinklers operate properly and you don't blow your connections apart. Always install a pressure regulator AFTER any control valves or backflow preventers.
These standard pressure regulators are available in three different pressure ranges and are used only with hose thread fittings and components. Use for drip tape, drip system, micro sprinklers. Pressure regulators should be installed after the filter.
Maximum operating inlet pressure is 100 PSI. Made of high impact UV resistant plastic.
The 10 PSI Pressure Regulator is recommended for hydroponic pump applications.
The 15 PSI Pressure Regulator is recommended for small drip systems.
The 25 PSI Pressure Regulator is recommended for use with larger drip systems and micro-sprinkler systems. |
|
|
|
|
|
|
|
Order #0018020
Standard Preset
Pressure Regulator 10PSI
3/4in FHT to 3/4in MHT
9.95 |
|
Order #0018010
Standard Preset
Pressure Regulator 15PSI
3/4in FHT to 3/4in MHT
9.95 |
|
Order #0018000
Standard Preset
Pressure Regulator 25PSI
3/4in FHT to 3/4in MHT
9.95 |
|
|
|
|
|
|
|
|
|
|
|
|
|
Half (1/2) Inch Supply Line Tubing
|
|
|
|
|
|
|
Soft Black
Vinyl Tubing
Our tubing is UV stabilized for long life when exposed to sunlight. Black tubing is recommended for use in water gardening because it practically disappears underwater, and since sunlight does not penetrate it, algae growth inside the tubing is inhibited. Perfect for hydroponic, irrigation, pond and waterfall applications as well. |
 |
|
|
|
|
|
Soft Black Vinyl Tubing
1/2 (.50) Inch Tubing (.50 ID / .625 OD)
Commercial grade flexible vinyl tubing is made of the highest quality resins and is UV resistant. Available by the individual foot or 100 foot roll. |
|
|
|
|
|
|
|
Order #0012250
Soft Black Vinyl
1/2 (.50) Inch ID Tubing
Each Foot
.49 |
|
Order #0015100
Soft Black Vinyl
1/2 (.50) Inch ID Tubing
100 Ft Roll
39.95 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
